De-sta-co 722 INTERMITTOR Manual de usuario

WARNINGThis is a controlled document. It is your responsibility to deliver this information to the end user of theCAMCO/FERGUSON product. Failure to d

8SECTION 4: InstallationThese units are manufactured to meet a specific set of design parameters. Any change to the load, size of dial, or speed of th

9SECTION 4: Installation (continued)4.1.5. Install dowels.4.1.5.1. Use a commercially available straight dowel of the appropriate size.4.1.5.2. Drill

10SECTION 4: Installation (continued)4.1.7. Check the adjustment of the switch cam if your unit has this option. To insure unitstops in dwell, see Fig

11SECTION 5: AdjustmentsThe Intermittor is a solid mechanical, backlash-free mechanism.There are no adjustments required onthe Intermittor during inst

12SECTION 5: Adjustments (continued)5.1.1. Clutch Adjustment DescriptionThe clutch must be adjusted to prevent any slippage during normal operation to

13SECTION 5: Adjustments (continued)5.1.4. Clutch Adjustment ProcedureCAUTION: OPERATIING THE INDEXER WITH THE CLUTCH NOT ADJUSTEDCAN CAUSE IMMEDIATE

14SECTION 5: Adjustments (continued)d. Apply power to the unit and check for clutch slippage.NOTE: When clutch is not slipping, entire clutch will rot

15SECTION 6: Maintenance6.1. Correct Lubricants – For the protection of the unit use only lubricants meeting thespecifications shown below in Chart 2.

16SECTION 7: TroubleshootingTROUBLESHOOTING GUIDESymptom Cause SolutionBacklash at output shaft Worn/damaged followers Replace(in dwell)Tight Stations

17SECTION 7: Troubleshooting (continued)TROUBLESHOOTING GUIDESymptom Cause SolutionOIL LEAKS AT:Seals Worn or damaged seal Replace seal; polish shaft

INTRODUCTIONThis manual is supplied to aid in the installation and maintenance of your Ferguson-brand index drive.When contacting Industrial Motion Co

18SECTION 8: Repair and Replace 8.1 Cam Follower Replacement8.1.1. Rotate camshaft to mid-dwell position. (See Figure 3)8.1.2. Drain oil and remove fr

19SECTION 8: Repair and Replace (continued)FOLLOWER NO. F-50 THROUGH F-400DISASSEMBLY:Remove setscrew and pull cam followerfrom hole using a draw hamm

20FOLLOWER NO. FM-100 & FS100 - FS-400DISASSEMBLY:Remove locknut, setscrew and follower.ASSEMBLY:Clean the follower and stud hole in theroller gea

21SECTION 8: Repair and Replace (continued)8.2. Oil Seal Replacement8.2.1. Remove oil seals by drilling a number of holes into the seal case.The seal

22SECTION 8: Repair and Replace (continued)8.2.12. Bottom out the tool or seal – to avoid cocking of the seal in the bore. This alsopositions the seal

23SECTION 8: Repair and Replace (continued)8.3.1. “R” Series (Ferguson) ReducersNOTE: The “R” Series reducer is a double enveloping worm gear type wit

24SECTION 8: Repair and Replace (continued)NOTE: Worm must be dropped before attempting to remove the gear.8.3.1.1.2. Gear8.3.1.1.2.1. Remove the worm

25SECTION 8: Repair and Replace (continued)8.3.1.1.3.2. The distance from the finished face of the housing to theunmarked face of the gear, noted at t

26SECTION 9: THINGS TO AVOIDAn Industrial Motion Control Indexer is a relatively simple mechanism using an input shaftmounted cam to drive roller foll

27UNIT CONFIGURATIONS, REDUCER MOUNTING POSITIONS, HAND OF CAM

1Table of ContentsSection Page1. General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-

© Industrial Motion Control, LLC 2003 All rights reservedThis publication is for information purposes only and should not be considered a binding P

2SECTION 1: General InformationThe Industrial Motion Control (IMC) Intermittor is engineered and manufactured to very high toleranceswhich necessitate

3SECTION 1: General Information (continued)1.2.4. Reducers should be of minimum backlash variety and directly coupled with abacklash-free connection.

4SECTION 1: General Information (continued)1.5. Requesting Service – Call our Technical Service Department in Wheeling, IL at1-800-645-5207 or 847-459

5SECTION 2: Overview The sketches contained in this document are for illustrative purposes only. They are intended torepresent standard components and

6SECTION 2: Overview (continued)2.2. Ferguson Reducer Location Map FIGURE 21. Housing2. Ring Gear (& separate spider for some units)3. Pinion Worm

7SECTION 3: SpecificationsModelStandard ReducerStandard AC Motorwith Air Clutch/Brake Standard 180 Volt DC Motor Output Shaft Torque LimiterInput Sha